Talk to a Mustang Sales Tech
1-877-887-1105
M-F 8:30A-11P, Sat-Sun 8:30A-9P
$20K Sweeps! 10 Chances to Win! Enter Daily >

Best Sellers

How to Install a Mustang Catted X-Box Mid-Pipe on Your 1999-2004 Mustang GT

Installation Time

3 hours

Tools Required
  • Lift or Jack Stands (4)
  • 22mm Wrench
  • Hand Tools
  • Cutting Device
  • Penetrating Oil

Thanks again for purchasing your new 409 stainless steel Pypes Performance Exhaust Ford Mustang off-road or street legal X-pipe. Please be sure to confirm all the components in the kit were received in your shipment before beginning installation. If you find any component missing, please contact our office at 800-421-3890 for replacement. Installation of this kit will require a few simple hand tools, a cutting device and penetrating oil. For a quicker and tighter installation, air tools are recommended. 
Technical assistance is available both online at www.pypesexhaust.com or 
800-421-3890. 


COMPONENTS


(A)  1 set  DFM36  Front Legs
(B)  1 set  XFM07  X-Box
(C)  2  HVC21  Clamp
(D)  1  XFMSLEEVE  Downpipe Sleeve


XFM17


1.  Begin by disconnecting your negative cable from your battery, as you will be disconnecting some electrical components. Place the vehicle on a lift or (4) jack stands at maximum height. This will aid in an easier installation.

Note: Make sure to support your catback just past the connection point between the factory h-pipe. 


2.  Unbolt the factory h-pipe from your cat-back. Soaking your factory mounting points with penetrating oil will allow for easier removal. Next, disconnect your 02 sensors from the factory wiring harness and remove them from the h-pipe using a 22mm wrench. Remove the bolts at the manifold/header end. Be careful, as old or rusty parts tend to break easily. On the passenger side header has a thin metal gasket which can be reused if not damaged. Any slight mark or bend in the metal will cause a leak at the header. A new gasket can be purchased from your local Parts Dealer.


3.  Begin by installing the driver and passenger side down-pipes/front legs ( Street legal versions using cats will require 8-1/2” to be cut off the down-pipes legs, further instructions below), snug the bolts but do not tighten. Note: 96-04 GT owners, make sure to install the metal gasket on the solid flange and the sleeve in the driver side leg. A small amount of RTV silicone will help hold the gasket in place. 


4.  Next, install the X-Box portion. Position the ball portion so that the long leg is on the driver side and the short leg is on the passenger side. Slide the (2) HVC21 band clamps on to the front legs of the x-pipe. Now, slide the x-pipe on to the driver and passenger down-pipes matching the ball ends to the cat-back. Re-install the factory cat-back hardware and snug tight. If hardware is necessary, you can purchase an HVC35 kit or 3/8-16 x 2-1/2” bolts, nuts and washers from a local hardware store.


5.  Supporting or jacking up on the center of the X-pipe will aid in the system having the most possible ground clearance. Finish by tightening all the hardware and then the (2) clamps, making sure the X-pipe is adjusted properly. Last, install all the 02 sensors and connect the wiring to the factory harness. 

Note: 99-04 owners should consider MIL Eliminators to insure proper computer 
and 02 sensor operation. 04 owners will require 24” 02 extenders.


6.  After all the connections are tight, start the engine. Check and listen for any leaks. 
Make sure to check your connections periodically as they may come loose.


XFM37


These 49 state street legal versions will follow the same instructions as above aside from two cuts in the down-pipes, the installation of the cats and (2) additional HVC21 band clamps. These additional instructions happen between steps 3 & 4 above. You will need to cut 8-1/2 inches off the back of the two down-pipes before installation. Next, install the clamps on the expanded/slotted end of the cat. Make sure the O2 sensor plugs are tight on the cats. 2004 GT owners can use the cats 02 sensors and plug the ones in the X-Box. Finish the install by sliding the cats on to the down-pipe legs and the H-Box into the back of the cats. 


*** Federal laws prohibit the use of HFM17 for street use. 
Check with local and state authorities for the legal use of HFM17 and HFM37.

Best Sellers