Talk to a Mustang Expert
Mon-Thu 8:30a-11p, Fri-Sun 8:30a-9p

Free Shipping on Everything. Seriously. Details

Roush Performance Heat Extractor Insert (13-14 GT)

AmericanMuscle no longer carries the Roush Performance Heat Extractor Insert (13-14 GT). Please check out 2010-2014 Mustang Hoods for an updated selection.
5 Reviews
Our Price


  • Item #69143
  • MPN# 421628

  • Market Price $24.99
  • You Save 20% ($5.00)
Choose options to add to cart

AmericanMuscle no longer carries the Roush Performance Heat Extractor Insert (13-14 GT). Please check out 2010-2014 Mustang Hoods for an updated selection.

Free Shipping on Everything
Customer Photos
  • Blocks water from entering cold air intake
  • Still allows engine heat to escape
  • Thick foam rubber construction
  • Simply installs into the underside hood insulator
  • Fits 2013-2014 GT and BOSS Mustangs w/ factory heat extractor hood
Blocks Incoming Water. Constructed from a thick foam rubber this Roush Insert Plug simply installs into the underside hood insulator to block outside rain water from entering your aftermarket cold air intake.

Heat Extractor Compatible. The Roush insert plug is designed to only block off the lower portion of the vent opening so it will still allow underhood engine heat to escape through the factory hood extractors.

Application. This Roush Performance Hood Vent Insert Plug is specifically designed to fit 2013-2014 GT or BOSS Mustangs with the factory heat extractor hood installed.

Fitment: 2013 2014 Details

What's in the Box
  • (1) Foam rubber insert
Installation Info
Will it fit my Mustang?
  • Boss 302 - 13
  • GT - 13, 14

Customer Photos (2) Submit Your Photo

View All 2 Photos

You Might Also Like

Q & A

No questions about this product yet.

Ask the First Question

More Products You Might Like

Customer Reviews (5) Write a Review

Overall Rating 4.2

out of 5 stars

  • 4/5

    January 24, 2014

    It works..

    This product works as stated it blocks the water from getting on the air filter. As for price little on the high side.



    Helpful (1) (0)

  • 4/5

    November 23, 2013

    Works as advertised

    As said in the title, the insert does it's job. Since putting it in I have not seen any water close to the intake. Don't be fooled by the pictures though, this simply a small piece of foam cut to fit the form of the heat extractor. That said, I think based on its construction it could be a bit cheaper, but I have no worries about water reaching my intake. It's not anything fancy, but again does what it's designed to do. I would much rather pay for this then have the airraid rainshield covering my intake.


    Atlanta, GA, USA

    Helpful (1) (0)

  • 5/5

    October 18, 2013

    does what its intended to do

    Put this in right before I washed my car. kinda skeptical at first so I covered my CAI and put a paper towel on top of the cover to see how well this product would work. Only 1 drop of water made it to the paper towel, and that could have been from opening the hood to get the cover and paper towel out. Definitely recommend


    Ohio, USA

    Helpful (1) (0)

  • 4/5

    October 21, 2013

    Simple but effective

    Fairly easy to install. Does the job. A great option!


    Setauket- East Setauket, NY, USA

    Helpful (0) (1)

  • 4/5

    September 24, 2013

    not sure if its worth it

    sigh, i guess i shouldve read the description a little better... it is just a rubber foam insert, my fault for not knowing what i realized is smaller than i thought, only covers up about a 1/4 of the vent opening and i hope it doesnt fall out.. it has rained here the past night and this morning, so far no signs of water getting on the CAI filter that ive installed, thats good news...bad news is it was 19.99...dont think it is worth that at all...other than that, i suppose if you are worried about keeping the CAI filter dry it works...


    West Palm Beach, FL, USA

    Helpful (0) (1)

Related Mustang Categories