FREE 1 to 3-Day Delivery on Orders $119+ Details
Instruction Manual P/N: 51-32642-B / 54-32642-B
Make: Ford Model: F-150 Year: 2015-2016 Engine: V6-2.7/3.5L (tt) EcoBoost
• Please read the entire instruction manual before proceeding.
• Ensure all components listed are present.
• If you are missing any of the components, call customer support at 951-493-7100.
• Ensure you have all necessary tools before proceeding.
• Do not attempt to work on your vehicle when the engine is hot.
• Disconnect the negative battery terminal before proceeding.
• Retain factory parts for future use
Label | Qty | Description | Part Number |
---|---|---|---|
A1 | 1 | Air Filter (Pro DRY S) | 21-91040 |
A2 | 1 | Air Filter (Pro-5R) | 24-91040 |
B | 1 | Seal, Trim (23") | 05-00072 |
C | 1 | Fitting, Air Temp Sensor | 05-01336 |
D | 1 | Tube | 05-32642B1 |
E | 1 | Housing | 05-32642B2 |
F | 1 | Coupling, Silicone Reducer | 05-01331 |
G | 1 | Coupling, Silicone Hump | 05-01332 |
H | 2 | Clamp 2-1/2" - 4-1/2" | 03-50006 |
I | 1 | Clamp 2-13/16" - 3-3/4" | 03-50008 |
J | 1 | Clamp, 2-5/16" - 3-1/4" | 03-50019 |
K | 1 | Grommet | 03-50167 |
L | 2 | M6 (x1x25) screw | 03-50114 |
M | 2 | M6 Flat Washer | 03-50070 |
N | 2 | M6 Lock washer | 03-50071 |
Tools required: 7mm nut driver, 8mm nut driver, 10mm socket & driver, & flat blade screw driver.
Note: Legal in California for use on race vehicles only. The use of this device on vehicles used on public streets or highways is strictly prohibited in California and others states that have adopted California emission regulations.
Step1: Rotate (1) temperature sensor counter clockwise 1/4 quarter turn then pull it out of the tube.
Step 2: Untighten the three (2) clamps on the air intake tube. Pull the tube out of the truck.
Step 3: Unclip the top of air box and remove the top half of the box and the air filter
Step 4: Install the grommet into hole on the back side of the in aFe tube then push the aluminum fitting in it.
Step 5: Install couplings and clamps onto tube ends. Do not tighten any of the clamps yet. Secure the intake tube to the housing using the provided bolts, lock washers, and flat washers.
Step 6: Install the air filter onto the tube, align the flat edge with the top of the airbox, and tighten the clamp.
Step 7: Install trim seal onto housing.
Step 8: Install the complete assembly into the truck by first lining up the tabs on the airbox and then lining up the couplings.
Step 9: Clip the airbox into place.
Step 10: Secure the temperature sensor into the aluminum fitting by turning clockwise 1/4 turn. Important: Make sure the plastic tab clips over the ramp on the top of the fitting.
Step 11: Make sure all clamps and screws are tight.
Your installation is now complete. Thank you for choosing aFePower.
To purchase any of the items above, view airflow charts, dyno graphs, photos, and video; please go to aFepower.com.
General Terms:
• aFe warrants their products to be free from manufacturer’s defects due to workmanship and material.
• This warranty applies only to the original purchaser of the product and is nontransferable.
• Proof of purchase of the aFe product is required for all warranty claims.
• Warranty is valid provided aFe instructions for installation and/or cleaning were properly followed.
• Proper maintenance with regular inspections of product is required to insure warranty coverage.
• Damage due to improper installation, abuse, unauthorized repair or alteration is not warranted. • Incidental or consequential damages or cost, including installation and removal of part, incurred due to failure of aFe product is not covered under this warranty.
• All warranty is limited to the repair and/or replacement of the aFe part. To request Return Goods Authorization (“RGA”), email [email protected] or call (951)493-7100. Upon receipt of the RGA, you must return the product to the address provided in the RGA, freight prepaid and accompanied with a dated proof of purchase and the RGA. Upon receipt of the defective product and upon verification of proof of purchase, aFe will either repair or replace the defective product within a reasonable time, not to exceed thirty days.
Product Category | P/N Prefix | Warranty duration |
---|---|---|
Direct OE Replacement Filters | 10, 11, 30, 31, 71, 73 | Life of the vehicle |
Racing Filters | 18 | 1 year |
Universal | 21, 24, 72 | 2 years |
Air Intake Systems | 50, 51, 54, 55, 75 | 2 years |
Exhaust Systems | 49 | 2 years |
Intercoolers & Intercooler Tubes | 46-2 | 2 years |
Intake Manifolds | 46-1 | 2 years |
Differential Cover | 46-7 | Life of the vehicle |
Exhaust Manifolds | 46 | 2 years |
Throttle Body Spacers | 46-3 | 2 years |
Fluid Filters | 44 | 90 days |
Pre-Filters | 28 | 2 years |
Heavy Duty OE Replacement | 70 | 2 years |
PowerSports OE Replacement | 81, 87 | 2 years |
PowerSports Intake Systems | 85 | 2 years |
No other warranty expressed or implied applies nor is any person or advanced FLOW engineering authorized to assume any other warranty. Some States do not allow the exclusion or limitation of incidental or consequential damages or do not allow limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from State to State.
advanced FLOW engineering, inc.
252 Granite Street Corona, CA 92879
TEL: 951.493.7155 • TECH: 951.493.7100
E-Mail:[email protected]