Free Shipping On Orders Over $49. Details

Talk to a Mustang Enthusiast
1-877-887-1105
M-F 8:30A-11P, Sat-Sun 8:30A-9P
Win $5,000 From Rovos! Enter daily!
Win Any MBRP XP Series Exhaust! Enter Daily

SR Performance Aluminum One Piece Driveshaft (11-14 GT)

AmericanMuscle no longer carries the SR Performance Aluminum One Piece Driveshaft (11-14 GT). Please check out 2010-2014 Mustang Driveshafts for an updated selection.
This item currently can not be added to your cart. Please try again later.

Features & Details

  • Lighter Than the Stock 2-Peice Design
  • Quicker Acceleration
  • More Responsive Engine
  • Seamless 1-Piece 6061-T6 Aluminum Tubing
  • 3.5" Diameter for Extra Clearance
  • Overall Length - 56.299 Inches (1430 Mm)
  • Fits 2011-2014 Manual and Automatic GT and BOSS Mustangs
Light Weight. Lighter and stronger than the clunky 2-piece stock driveshaft, this SR Performance Aluminum One Piece Driveshaft greatly reduces rotating mass to improve your Pony's 1/4 mile track times.

Superior Quality. Constructed from 3.5" diameter 0.125 inch wall thickness 6061-T6 aluminum tubing for strength, this 56.299" (1430 mm) long driveshaft features 1350 Series Dana Spicer 5-1350X Universal Joints with 1350 series flange yokes front and rear with no adaptor required for installation.

Extra Clearance. This light weight one piece aluminum driveshaft features a 3.5" diameter design, giving you the extra clearance needed to avoid interference that can happen on lowered Mustangs equipped with a standard 4" shaft.

Application. This SR Performance Aluminum One Piece Driveshaft is specifically designed for use on 2011 to 2014 GT or BOSS Mustangs equipped with either a 6-speed manual or automatic transmission.

Fitment: 2011 2012 2013 2014 Details

MPN# 384412

CA Residents: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

What's in the Box
  • (1) Driveshaft
Installation Info
Tech Specs
Will it fit my Mustang?

You Might Also Like

Customer Photos

More Products You Might Like

Questions & Answers (4)

4 Top Rated Questions

what is the weight of the stock 2 piece drive shaft?

  • The factory 2 piece driveshaft weighs approximately 43 lbs.

Helpful (1)

What is the weight?

  • The weight of the Aluminum One Piece Driveshaft (11-14 GT) is 27lbs.

Helpful (1)

What horsepower is this rated to?

  • This driveshaft is rated for 800 HP.

Helpful (0)

Will driveshaft Item #384412 work with v6 auto trans and GT rear end?

  • No, the V6 driveshaft is a different length.

Helpful (0)
Post Your Question

Recommended For You

Customer Reviews (6) Write a Review

Overall Rating 4.8

out of 5 stars

Installation Time:Full Day

Installation Cost:$100-$250

  • Performance Gain 5 5
  • Fit 5 5



  • 5/5

    Installation Time: Afternoon

    February 05, 2018

    Dana one piece drive shaft.

    It fit well and is ALOT lighter.The only issue I had was the factory bolts for the rear half were too long.I ended up cutting them down to fit and needed to install them in a certain order which is why it took me about 2 hours.Cant try it out as there is 3 feet of snow up here,lol.

    NelsJ

    Year: 2012 Submodel: GT

    Helpful (9)

  • 5/5

    Installation Time: Afternoon

    May 23, 2017

    Installed

    Straight forward install. Went in with no struggle or modifications. Great fitmentertainment and noticeable improvement or stock 2pc shafts both in driving feel and performance

    AlexD

    Year: 2013 Submodel: Boss

    Helpful (9)

  • 5/5

    Installation Time: Full Day

    April 04, 2017

    Great item.

    This is a great driveshaft! Was a little skeptical on getting the SR over the driveshaft shop, but I could not be happier with this, install and fit was perfect and works great!

    richard

    Year: 2011 Submodel: GT

    Helpful (8)

  • 5/5

    Installation Time: Shop Install

    Installation Cost: 0-$100

    December 10, 2015

    Great Product

    Driving an automatic 5.0 my car felt slugish so after brainstorming I added the drive shaft to the mix of mods that I have done so far which include, Long Tube Headers, Off Road X, AirRaid Intake, 90 mm throttle, custom tune and full suspension mods. The driveshaft came quickly and safely and seriously transformed the way the car revs and launches off the line now. This is also a Nice peace of mind mod. I highly recommend this product!

    tybad

    Year: 2013 Submodel: GT Canton Michigan

    Helpful (12)

  • 5/5

    Installation Time: Shop Install

    Installation Cost: $100-$250

    May 29, 2015

    Very nice piece

    Twisted the stock DS and had the car towed to dealership that's the only reason for shop install. Called to ask about who manufactures this one because it isn't listed and come to find out it's actually made by Dana which is one of the most trusted companies in the off road industry. Car definitely spins up faster now And having the CV at the diff is really nice for lowered cars cuz it corrects the pinion angle without the need for adjustable control arms

    bond

    Year: 2014 Submodel: GT Manhattan, KS

    Helpful (10)

  • 4/5

    Installation Time: Afternoon

    May 14, 2015

    driveshaft

    Driveshaft is great the only problem is it come with no installation hardware for the rear end stock hardware is to long. Nor does american muscle have the hardware for it.. so I ended up using Allan head grade8 40mm long from homedepot. This one weighed 20lbs so save your self the headache and buy there 19lb shaft.

    mark

    Year: 2014 Submodel: GT new your

    Helpful (10)

Related Mustang Categories