Free Shipping On Orders Over $49. Details

Talk to a Mustang Enthusiast
1-877-887-1105
M-F 8:30A-11P, Sat-Sun 8:30A-9P
Win $5,000 From Rovos! Enter daily!
Win Any MBRP XP Series Exhaust! Enter Daily

Dana Spicer Aluminum One Piece Driveshaft - 4 in. (05-10 GT)

AmericanMuscle no longer carries the Dana Spicer Aluminum One Piece Driveshaft - 4 in. (05-10 GT). Please check out 2010-2014 Mustang Driveshafts for an updated selection.
This item currently can not be added to your cart. Please try again later.

Features & Details

  • Reduces Rotating Mass for Better Performance
  • Lighter and Stronger Than Stock 2-Peice Design
  • Seamless One Piece 6061-T6 Aluminum Tubing
  • 4" Diameter 0.125 Inch Wall Thickness
  • Overall Length - 52.598 Inches (1336 Mm)
  • Built, Assembled and Balanced by Dana Spicer
  • Fits All 2005-2010 GT and Bullitt Mustangs
Improves Performance. Lighter and stronger than the clunky 2-piece stock driveshaft, this Dana Spicer One Piece Aluminum Mustang Driveshaft greatly reduces rotating mass to improve your GT's performance for quicker 1/4 mile track times.

Superior Quality. Constructed from 4" diameter 0.125 inch wall thickness 6061-T6 aluminum tubing for strength, this 52.598" (1336 mm) long driveshaft features 1350 Series Dana Spicer 5-1350X Universal Joints with 1350 series flange yokes front and rear with no adaptor required for installation.

Application. This Dana Spicer One Piece Aluminum Driveshaft is specifically designed for use on 2005 to 2010 GT and Bullitt Mustangs equipped with either a 5-speed manual or automatic transmission.

Fitment: 2005 2006 2007 2008 2009 2010 Details

MPN# 10001767

CA Residents: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

What's in the Box
  • (1) Driveshaft
Installation Info
Tech Specs
Will it fit my Mustang?

You Might Also Like

Customer Photos

More Products You Might Like

Q & A

No questions about this product yet.

Ask the First Question

Recommended For You

Customer Reviews (3) Write a Review

Overall Rating 3.3

out of 5 stars

Installation Time:Less than 1 Hour

  • Performance Gain 3.666667 3.7
  • Fit 3.666667 3.7



  • 4/5

    Installation Time: Less than 1 Hour

    May 18, 2018

    More Horspower, more torque, no clearance Problems

    No clerance problems if you add a 1/2 inch spacer on rear axle mount on lowered Mustangs. It's not necessary to cut away any pieces or parts at all, to prevent rubbing !!!!! Trust me I'm a german engineer! Only 4 Stars, cause you have to install a spacer and remeasure your driveshaft pinion angle. With this little erfort you can drive a big 4 Inch driveshaft and you can increase horsepower, cause the 4 Inch driveshaft can go on more horsepower and more torque then the 3 1/2 Inch Driveshaft. Hope this helps.

    Raceface

    Year: 2005 Submodel: GT

    Helpful (7)

  • 5/5

    Installation Time: Less than 1 Hour

    November 14, 2015

    my 08 mustang gt

    My Dana Spicer 4 driveshaft was easy to install and works great had a vibration in my stock driveshaft put my Dana in and cleared it right up and cost cheaper

    dunklemustanggt

    Year: 2008 Nelsonville ohio

    Helpful (9)

  • 1/5

    Installation Time: Less than 1 Hour

    October 16, 2015

    dont buy if you have a lowered mustang

    Dont buy the 4 inch drive shaft if you have a lowered mustang.buy the 3 1/2 inch.Had to cut away parts of the tunnel for clearance.learned the hard way.

    quickRick

    Year: 2006 Submodel: GT cooper city,florida

    Helpful (15)

Related Mustang Categories