Talk to a F-150 Sales Tech
1-888-706-1096
M-F 8:30A-11P, Sat-Sun 8:30A-9P
$20K Sweeps! 10 Chances to Win! Enter Daily >

How to Install Rough Country 4 in. Suspension Lift Kit on your F-150

Tools Required
  • 5mm Allen Wrench
  • 8mm Allen Wrench
  • 8mm wrench /socket
  • 10mm wrench /socket
  • 12mm Wrench
  • 13mm wrench / socket
  • 15mm wrench /socket
  • 16mm wrench /socket
  • 17mm wrench /socket
  • 18mm wrench /socket
  • 19mm wrench /socket
  • 21mm wrench /socket
  • 22mm wrench /socket
  • 24mm wrench /socket
  • 30mm wrench /socket
  • Floor Jack
  • Jack stands
  • Reciprocating Saw
  • Hammer
  • 9/16 wrench /socket
  • 1 1/16” Wrench
  • Dril
  • 41/64” Drill Bit
  • 11/32” Drill Bit
American Muscle
Shop Parts in this Guide



1. Chock the rear wheels and jack up the front of the vehicle.

2. Place jack stands under the frame rails and lower onto jack stands.

3. Remove the wheels/tires using a 21mm socket. 4. Remove the skid plate with a 13mm socket. See Photo 1. On 2011 and newer models, remove the EPAS (Electronic Power Assist Steering) Plugs as shown. See Photo 2. This must be done BEFORE installation is started.


5. Remove tie-rod end using a 21mm wrench. Using a hammer hit the side of the knuckle to pop tie-rod out. Photo 3.

6. Remove the ABS and brake line bracket from the knuckle using a 8mm wrench for the ABS wire and a 10mm wrench for the brake line bracket. Retain hardware for reuse. See Photo 4.



7. Using a 19mm socket & 21mm wrench, remove brake caliper as shown in Photo 5. 8. Hang caliper out of way. Do not let caliper hang by brake hose as this will damage hose. Retain factory hardware for reuse and remove the rotor. See Photo 6.


9. Remove the dust shield using a 8mm socket. See Photo 7. 10. Remove the ABS wire from the bearing assembly using a 5mm allen wrench. See Photo 8.






11. Loosen the upper ball joint nut using a 21mm wrench. Tap lightly with a hammer to release ball joint from knuckle. See Photo 9.

12. Loosen the lower ball joint using a 24mm wrench. Tap lightly with a hammer to release ball joint from knuckle. See Photo 10.

13. Remove the upper and lower ball joint nuts and remove the knuckle from the vehicle. 14. Remove the sway bar links from the sway bar using a 19mm wrench. Retain hardware for reuse. See Photo 11. 15. Remove the lower strut bolt using a 30mm socket and 1 –1/16” wrench. See Photo 12. Retain hardware for reuse. 


16. Remove the sway bar from the frame mount using a 15mm socket. Please note the position that the sway bar is installed from the factory to make sure it is reinstalled correctly. Retain hardware for reuse. See Photo 13.

17. Remove the lower control arm using a 21mm and 1-1/16” wrench. Retain hardware for reuse. See Photo 14.



18. Remove the strut from the upper mount using a 15mm socket / wrench. Retain hardware for reuse. See Photo 15.

19. Remove the bearing from the stock knuckle with a 18mm socket. See Photo 16.



20. Lay the new supplied lifted knuckle on the bearing and insert the factory bolts. Tighten with a 18mm socket. See Photo 17.

21. Depending on the brake caliper bolt size, the knuckle may need to be drilled. If the stock bolt is 16mm the caliper mounting location will need to be enlarged using a 41/64” drill bit. Trial fit the stock caliper bolts to make sure the caliper needs to drilled before drilling. See Photo 18.



22. Install the front and rear cross-member using the factory hardware. See Photo 19. Do not tighten at this time.

23. Install the sway bar drop brackets using the factory nuts and a 15mm wrench. See Photo 20. 





24. Install the lower control arms using the supplied 18mm x 160mm cam bolts, washers and nuts. See Photo 21.Do not tighten at this time.

25. Install the supplied 10mm studs in the strut spacers on the end with the smallest holes. Use a 17mm wrench or socket to pull the stud into place as shown in Photo 22. 

26. Using the stock hardware, install the strut spacers on the struts. Tighten using a 15mm socket. See Photo 23.

27. Install the strut with strut spacers installed in the stock upper mount. Secure with supplied 10mm nuts, washers and lock washers. Do not tighten at this time.

28. Install the lower strut in the lower control arm using the factory hardware. Tighten using a 30mm and 1-1/16” wrench. See Photo 24.

29. Tighten upper strut mount hardware using 17mm wrench. 



30. Using a 10mm wrench remove the brake line bracket from the driver and pass side frame. See Photo 25.

31. On the passenger side remove the brake line from the two factory clips. 32. Install the new brake line bracket on the driver and passenger side with the stock hardware. See Photo 26.



33. On the driver side, pull slightly on the brake line to allow the line to be installed on the new bracket. Secure the brake line to the new bracket with the supplied 5/16” x 3/4” bolt, washers and nut. See Photo 27.

34. Install the factory passenger side brake line in the new bracket using the supplied 5/16’ x 3/4” bolt, washer and nuts. See Photo 28. 



35. Install the sway bar body on the sway bar links located on the lower control arms. Install nut to hold the sway bar in place but do not tighten at this time. See Photo 29.

36. Swing up the sway bar and install on the sway bar drop brackets using the supplied 3/8” x 1” bolts, washers and nuts. Tighten using a 9/16” on the sway bar drop hardware and 18mm wrench on sway bar links on the lower control arms. See Photo 30.



37. Install the new knuckles using the stock hardware on the lower ball joints, making sure the half shafts are installed in the bearing assembly. Tighten using 24mm and a 12mm wrench. Do not use air impact on the upper and lower ball joint, tighten with hand tools.

38. Install the knuckle on the upper ball joint with the stock hardware and tighten using a 21mm and a 10mm wrench. Do not use air impact on the upper and lower ball joint, tighten with hand tools.

39. Install the ABS wire on the bearing assembly using a 5mm allen wrench. See Photo 31.

40. Install the dust shield with stock bolts and a 8mm socket. See Photo 32.



41. Install the rotor and caliper on the knuckle with the stock hardware using a 19mm or 21mm wrench. On models with 16mm caliper hardware it will be necessary to use the qty 4, two per side 5/16” thick washers on the head of the caliper bolts. Failure to use these washers on the 16mm bolts will allow the caliper bolt to protrude on the rotor side and can cause clearance issues. Tighten hardware. See Photo 33.

42. Install brake line bracket with factory bolts. Make sure the ABS wire are out of harms way. Using the supplied zip tie, secure the vacuum hose and ABS wire to the knuckle neck. See Photo 34.




43. Install the tie rod end in the knuckle and tighten using a 21mm and 10mm wrench. See Photo 35. Do not use air impact on the upper and lower ball joint, tighten with hand tools.

44. Install the tires and wheels using a 21mm socket. Remove the jack stands and lower the truck to the ground.

45. Install the two connectors on the rack and pinion.

46. Tighten the lower control arm bolts using a 1-1/16” wrench and socket. Torque to 200 ft/lbs.


REAR INSTALLATION

1. Chock the front tires and jack the rear the rear end up. Put jack stand under the frame rail and lower truck onto jack stands.

2. Remove tires and wheels using a 21mm socket. 3. Remove rear shocks from the upper and lower mount using 18mm and a 15mm wrench. See Photo 1 & 2. Retain the stock hardware. 





4. Using a 10mm wrench, remove the brake line assembly on the inner driver side frame rail. See Photo 3.

5. Install the brake line extension bracket on the frame using the stock hardware and tighten using a 10mm wrench. See Photo 4. 6. Install the brake line assembly to the new bracket using the supplied 3/8” x 1” bolt, washers and nut. Tighten using a 9/16” socket and wrench. See Photo 4.

7. Separate the e-brake cable as shown on the drivers side and remove the e-brake cables from the frame mount as shown in Photo 5 & Photo 6.


8. To install the new e-brake bracket measure from the rear measure 1 5/8” and from the bottom measure up 1 3/8” and mark hole to be drilled. See Photo 7 & 8.



9. Drill hole using a 11/32” drill bit. See Photo 9. 10. Install the new bracket as shown with the supplied 7/16” x 1” bolt, washers, nut in the factory hole and 5/16” x 3/4” bolt, washer and nut in the drilled hole. See Photo

10. Tighten using a 19mm and 13mm socket / wrench. 



11. Using a jack support the rear end and remove U-bolts using a 21mm socket and remove the factory blocks. See Photo 11.

12. Install the supplied block under the factory block, align the block pin holes on the axle and raise the axle into place. See Photo 12.






14. Install the new shock absorbers in the upper and lower mounts using the stock hardware. Tighten using a 18 and 15mm wrench. *Note* the body of the shock goes toward the axle mount.

15. Install the tire and wheels.

16. Raise up the rear of the vehicle and remove the jack stands. Lower the vehicle to the ground. 17. Install the e-brake cable in the new mount and reattach the e -brake cables on the frame. See Photo 13.