Win $17,760 For Your Truck! Enter Now!
Talk to an F-150 Expert
1-888-332-7930
Mon - Sun, 8:30 AM EST - 11:00 PM EST

3 More Days for Free Shipping! Get it by Dec 24th available on most items - Details

Roush Cold Air Intake (17-18 Raptor)

Market Price $409.99 You Save 2% ($10.00)
Starting At

$399.99

FREE Shipping
  • Item T527894-AC
  • MPN# 421981

Will this fit your F-150?

Features & Details

  • Provides Up to 25% Less Intake Restriction than Factory
  • Increases Induction Noise & Performance Sound
  • Performance Gains of 15 HP and 18 lb-ft. TQ
  • Injected-Molded Airbox
  • 105mm Mass Air Flow Tube
  • Reusable High Flow Dry Air Filter
  • NO Computer Tune Required
  • Simple Bolt-On Installation
  • CARB EO Number: D-418-30
  • Fits All 2018-2018 F-150 Raptor Models
Big Power Gain Potential from a Flexible CAI Setup. Slash intake restriction by a quarter with the installation of the Roush Cold Air Intake – a component from a company that makes hard-charging racing-related products – in your 2018-2018 Raptor. With a full airbox surrounding the filter element, this CAI features precision CAD design to create a very tight fit between the molding and the underside of the hood to block away engine heat. If you opt to install the 85mm stock MAF, you can expect a power boost of +10 hp and +8 ft-lbs of torque. With a 105mm MAF installed, your truck will develop a ripsnorting +15 horsepower and +18 ft-lbs.

Tuning Needed for Certain Options. The Roush Cold Air Intake may need an aftermarket tune or not depending on how you decide to set it up during installation. If you choose the 85mm stock MAF, no tuning is required – the OE tune is enough. However, if you select the greater power of the 105mm MAF, then an aftermarket tune is needed to make the intake functional.

Dry, Washable, Oil-Free Filter. The Roush Cold Air Intake features a dry filter element that is oil-free and does not require re-oiling at any point in the future. This filter can be washed (which is usually not required until approximately the 100,000 mile mark) and reused again and again. It is a high capacity performance filter made out of fabric strengthened with two layers of fine wire mesh.

Built to Stand Up to Long Use. The Roush Cold Air Intake is made from high-impact, breakage-resistant polyethylene plastic. The airbox is injection-molded plastic, with an EPDM foam heat shield seal to form a better bond with the underside of the hood. A roto-molded intake tube with a black textured surface is attached to this. The component also includes a heat extractor foam insert. The clamps are fabricated from steel. As the icing on the cake of quality the component is 100% made in the USA.

Choice of MAF Housing for Power Level. When installing the Roush Cold Air Intake, you can choose between setting it up to accept the 85mm stock MAF (lower power, no tune required) or a 105mm aftermarket MAF (higher power, tune required, MAF must be purchased separately).

Installs as a Replacement for Stock. As a direct fit replacement part for the stock air intake, the Roush Cold Air Intake bolts onto the same mounting positions. No additional drilling, cutting, etc. is needed for installation. The intake is supplied with the hardware and instructions needed for fitment.

3 Month Limited Warranty. The Roush Cold Air Intake comes with a 90 day limited manufacturer’s warranty against defects in workmanship and materials.

CARB Exempt, Usable in all 50 States. Designed to 50-state legal and usable anywhere from the coastal highways of California to the remote roads and trails of Upper Midwest, the Roush Performance Cold Air Intake Kit is fully CARB certified. It bears the CARB EO Number #D-418-30. This entitles you to drive it on-road as well as off-road in any location where CARB regulations apply, provided that it is installed so that the CARB compliance sticker is visible when the engine is inspected.

Application. This Roush Performance Cold Air Intake Kit is specially designed to fit the 2018-2018 F-150 Raptor equipped with the High Output (H.O.) 3.5L EcoBoost V6 engine.

Fitment: 2017 Details

What's in the Box
  • (1) Air Box
  • (1) Filter Tube
  • (1) Clean Air Tube
  • (1) Filter with Clamp
  • Hardware
Tech Specs
Cold Air Intake Specifications
Engine: 3.5L EcoBoost Filter Placement: Engine Bay
Material: Thermoplastic Finish: Black
Manufacture: Roush Performance Computer Tune Required: No

Rear Wheel HP and Torque Performance Gains
HP Gain: 15 RWHP Torque Gain: 18 ft/lb
Will it fit my F-150?

Customer Photos (1) Submit Your Photo

View 1 Photo

You Might Also Like

Q & A

No questions about this product yet.

Ask the First Question

More Products You Might Like

Reviews

Related F-150 Categories