Free Shipping On Orders Over $49. Details

Talk to a Mustang Enthusiast
1-877-887-1105
M-F 8:30A-11P, Sat-Sun 8:30A-9P
Win $5,000 For Your Mustang! Enter Daily

Street Fighter AOD Lockup Torque Converter w/ Anti-Balloon Plate (80-93 V8)

Item 25302
AmericanMuscle no longer carries the Street Fighter AOD Lockup Torque Converter w/ Anti-Balloon Plate (80-93 V8). Please check out 1979-1993 Foxbody Mustang Transmission Parts for an updated selection.

Features & Details

  • Great for Street and Strip
  • Lowers ET's
  • Anti-Balloon Plate
  • 3,000 RPM Stall
  • For Use with AOD Automatic Transmission
  • Fits 1980-1993 V8 Mustangs
Great for Street and Strip. Featuring furnace-brazed fins, needle bearings, and flame-hardened pre-ground pump hub, this computer balanced TCI StreetFighter torque converter will increase torque multiplication, and efficiency making this a great torque converter for both street and strip applications.

3000 RPM Stall. Increasing the rpm stall speed of your Mustangs torque converter will result in the engine reaching the powerband earlier, providing quicker acceleration and lower elapsed times. This TCI Street Fighter Torque Converter is set to 3000 RPM, that is a 1500 increase over stock.

Anti-Balloon Plate. An anti-ballooning plate helps reinforce the front and rear covers of the torque converter to control expansion due to the extreme fluid pressures developed within the converter by extremely high output engines or by the addition of force induction.

Application. This TCI Street Fighter Torque Converter is specifically designed for use on 1980 to 1993 high performance V8 Mustangs with the AOD automatic transmission.Functional lock-up torque converter, only for lock-up transmissions.

Fitment: Details

CA Residents: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

What's in the Box
  • (1) Torque converter
  • (4) Nuts
Installation Info
Will it fit my Mustang?

    Customer Photos

      Questions & Answers (6)

      5 Top Rated Questions

      Would this be the recommendation for a b303 cam swap in a 94 5.0 with a 1986 Aod ? I’m planning on a 4.10 rear gear

      • This TCI Street Fighter AOD Lockup Torque Converter has a 3000RPM stall speed, and would work well with the setup you described.

      Helpful (2)

      with this converter on an AOD, can this converter be used in an AOD with a 1 piece input shaft?

      • The Street Fighter AOD Lockup Torque Converter can be used with 1 piece input shafts.

      Helpful (1)

      Will this work well with a pretty much stock engine and cam?

      • This would still work fine with your car with a stock motor but recommended for more modifiedcars. 

      Helpful (1)

      Will this work with the stock flex-plate? Does the anti-ballon plate create the need for spacers, or can I simply take out my old stock convertor and replace it with this one?

      • The TCI Street Fighter AOD Lockup Torque Converter w/ Anti-Balloon Plate will bolt onto your factory, or aftermarket flex plate as long as the flex plate is designed for the vehicle. No additional parts or spacers are required to install this torque converter.

      Helpful (1)

      Can i install a non lockup converter on a stock 1991 aod transmission? Thanks ahead

      • The TCI Street Fighter AOD Lockup Torque Converter is a lock up converter. Installing a non lockup converter will physically require no additional parts, however since a non lockup converter creates significantly more heat, we would recommend an upgraded trans cooler if you go that route.

      Helpful (0)
      Post Your Question
      1 More Question
      do you have the front seal on the AOD transmission that the torque converter slides into what is the part number. 1 answer

        Customer Reviews (4) Write a Review

        Overall Rating 4.8

        out of 5 stars

        Installation Time:Full Day

        • Performance Gain 4.666667 4.7
        • Fit 5 5



        • 5/5

          Installation Time: Weekend

          August 09, 2017

          good choice

          replaced old converter with similar stall TCI converter. Same physical size, no installation problems and a decrease in 60foot time from 1.75 to 1.64 with no other changes. Good choice for me.

          nickg

          Year: 1990 Submodel: LX

          Helpful (10)

        • 5/5

          June 22, 2017

          Awesome!!

          Definitely worth it wakes the car up by getting you off the line much quicker. If your thinking about getting it just pull the trigger you won't regret it!

          Christopher

          Year: 1993 Submodel: Cobra

          Helpful (12)

        • 4/5

          July 12, 2016

          great deal and fit

          Ordered this took 3 days to receive it free shipping great fit 4 hour to swap out car is totally different

          silverbullet

          Year: 1993 Submodel: GT

          Helpful (12)

        • 5/5

          Installation Time: Afternoon

          August 18, 2014

          Great product and must have for power

          I installed this during a motor power upgrade. My cam needed a 2600-2700 stall, so this TCI 3k stall was a good fit. It works great and the install was straight forward. The instructions were good. The power transfer is good and it launches very solid. Love it!!

          DetroitGasMan

          Year: 1991 Submodel: Other Detroit, MI, USA

          Helpful (12)

        Related Mustang Categories