JLT Cold Air Intake (96-04 GT)

JLT Cold Air Intake (96-04 GT)
Click to Enlarge

TRANSCRIPT

Hey guys, Mike Wilson here from AmericanMuscle.com, today I’m here with the JLT cold air intake kit, for the 96-04 Mustang GT. This kit gets rid of your factory restrictive airbox and replaces it with a fender mounted air filter, and a high flow inlet tube, which will increase the airflow to your Mustang’s engine. This will give you more horse power, increase throttle response, and give you a deep throaty engine sound, and also enhance the under hood appearance with a black finish. The JLT cold air intake kit comes with a high flow reusable air filter, the lower intake tube, the upper intake tube, heat shield, and all the hardware. But first, we’re going to make a stock dyno run so we have some basic horse power and torque numbers to work from. Stock, our 2000 GT put down 221 horse power and 260 ft/lbs of torque. We just finished our stock dyno run, so now we’re going to install our cold air intake kit which should take less than an hour’s time using simple hand tools. On 96-01 Mustangs with an intake air temperature sensor, you’ll need to drill a ¾” hole in the inlet pipe, and use the rubber grommet to install the sensor into the pipe. We suggest using a very small amount of lubricant on both the inside of the grommet, and the inside of the sensor collar, to fit it back into the pipe. Even though this is a no tune required intake, we installed one of our Bama performance 93 octane race tunes to maximize our power gains. A custom tune from Bama performance adjusts engine parameters to maximize performance, through optimized air/fuel ratio, spark advance, enhanced throttle response, and for automatics, increased shift firmness and adjustable shift points. Now let’s make another dyno run, and see what kind of horse power and torque numbers we get. With a JLT cold air intake kit, and our Bama performance tune, our car put down 244 horse power and 287 ft/lbs of torque, gaining as much as 30 horse power and 48 ft/lbs of torque throughout the curve. We installed our JLT cold air intake kit along with our Bama performance custom tune in under an hour’s time using simple hand tools, and we picked up as much as 30 horse power and 48 ft/lbs of torque throughout the curve. The kit was really easy to install and looks great under the hood.
... READ MORE

About JLT

JLT Performance Cold Air Intakes
JLT Performance is a family owned business driven by a passion for Mustangs. Owned by Jay and Lisa Tucker, JLT Performance started in 2004 with one product for the 03, 04 Cobra and has grown to a never ending product line for nearly every late model Mustang out there. They understand the need for products that not only work, but look good and are affordable too. They feel they have some of the best products on the market and stand behind their products 100%, giving superior customer service. Being MADE IN THE USA, JLT and American Muscle make a winning team!
... READ MORE
OUR PRICE$229.99
Market Price $254.99You Save 10% ($25.00)
Item # 62000
AmericanMuscle no longer carries the JLT Cold Air Intake (96-04 GT). Please check out Mustang Cold Air Intake Kits for an updated selection.
Email

Product Features

  • Increases of 8 to 12 more horsepower
  • Better throttle response
  • Reusable S&B high flow air filter
  • Gloss Black Finish
  • Easy installation
  • Fits 1996-2004 4.6L V8 GT Mustangs
More Usable Horsepower. With a JLT Performance Cold Air Intake installed under the hood of your 1996 to 2004 GT you can expect to see average gains of 8 to 12 more horsepower at the rear wheels across the entire RPM range. In addition to an increase in horsepower you will also see an impressive improvement in throttle response.

Fender Well Induction. This JLT Cold Air Intake is designed to draw in cold air from the fender well, rather than the hot engine compartment. Which reduces the incoming air temperature for better combustion resulting in more horsepower.

Money Saving Reusable Filter. This JLT cold air intake kit comes complete with a high flow reusable S&B brand air filter. So that means there is no need to go out and buy a new filter every few thousand miles. Now you can just clean the filter, re-oil it, save money, and go!

Easy Installation. The JLT Performance Cold Air Intake kit was designed to install with just basic hand tools. No extra modifications or special tools are required for an easy 1 hour installation. And with the include tapered reducer it will fit throttle bodies up to 75mm in size.

Application. This JLT Performance Cold Air Intake System is specifically designed for use on the 1996 to 2004 GT Mustangs equipped with the sohc 4.6L V8 engine and does not require re-tuning the vehicles computer for operation. Does not fit Bullitt Mustangs.

Technical Note: 1996 to 2001 Mustang owners with an IAT sensor will need to drill a ¾” hole using a pnel or spade drill in the bottom side of the inlet pipe and use the supplied rubber grommet to install the sensor into the JLT pipe.

Cold Air Intake Specifications
Year/Model: 96-04 GT Filter Placement: Inside Fender
Material: PVC Finish: Black
Manufacture: JLT Computer Tune Required: No

Installation Time:

(approx) 1 Hour

Difficulty Level:

Simple installation for anyone.

What's in the box?

Hardware included:
  • (1) 6-inch filter
  • (3) band clamps
  • (4) MAF adapter screws
  • (2) Gaskets and deals
  • (1) Fenderwell adapter plate

What's in the box?

Hardware included:
  • (1) 6-inch filter
  • (3) band clamps
  • (4) MAF adapter screws
  • (2) Gaskets and deals
  • (1) Fenderwell adapter plate
checkmark
Fitment:
  • GT 96, 97, 98, 99, 00, 01, 02, 03, 04

Customer Reviews