(approx) 1 Hour
Simple installation for anyone.
$125.99 (set of 4)FREE Shipping Market Price $137.99 You Save 9% ($12.00)
Add Local Shop Installation
Saved - View your saved items
We're sorry. We couldn't save this product at this time.
Justin: The Front and Rear LED Side Markers that we have here today will appeal to the 2015 and newer Charger owners out there who wanna completely black out the markers themselves while at the same time adding some unique LED lighting in the process. Now, this set will include two amber markers for the front along with the two red markers for the rear. And they can be had all for right around that low to mid $100 price point.Install is gonna be a simple plug-and-play job here, guys, no wiring whatsoever, therefore, figure a soft one out of three wrenches on the difficulty meter. Site calls this an hour to complete from start to finish, which you should be able to bang it out a lot quicker than that. But either way, hang with me till the end of the video and we'll show you how it's done.All right. So, first things first here, guys, I do wanna say that if you're just simply looking to smoke the marker lights on your Charger, you can certainly save a few bucks and go with a traditional vinyl tint kit instead. We do have a few different options here on the site in that regard, in addition to some other LED options as well. So, as always, feel free to check out the entire selection before ultimately pulling the trigger.Now, there's other options aside if you dig the smoked or, in this case, the blacked-out look and would like to add some brightness along with a unique lighting pattern, then these markers might just be worth a look. Now, let's talk about that unique lighting pattern a little bit more because, unlike the factory markers that utilize kind of a single dull incandescent bulb, these options are gonna utilize more of that high-intensity LED strip that will illuminate in the center of the marker, basically, the entire length of the marker itself.Now, again, compare that to a factory housing, especially one that has been covered with some smoked vinyl and you're gonna see that light output is not only kind of dim and dull, but it's only in one spot of the marker. So, these, again, are just gonna be a lot brighter even with that smoked look, but also giving you that unique appearance as well. Now, those LEDs are gonna be housed in the ABS plastic base here, again, being topped off with that smoked polycarbonate lens, having given the DOT and SAE stamp of approval, which does make these guys legal for use in all 50 states.Now, the housings themselves will be a carbon copy, if you will, of the factory lights at least from a design or footprint aspect, meaning they're gonna be a direct replacement without the need for any modification. On top of that, as you guys can see it's a plug-and-play job here, guys. No need for wiring or anything like that, which means the install is going to be a breeze. Now, to give you a better idea of just how easy things will go down in the driveway or garage, feel free to check out our detailed walkthrough now.Man: Tools used for this installation, clip removal tool, T20 Torx bit, a 1/4-inch drive ratchet. Hey, guys, I wanna show you how to install our LED marker lights on our 2015 Charger. It's a pretty easy installation. Let's get started. First thing we're gonna do to get our marker light out is we're gonna move our wheel inside here and turn it inward, that way we can get to our push clips right here. That's gonna let us remove our wheel well, push it out of the way, and get behind here where we have Torx bolts holding in this marker light. So, we'll get started by removing our push clips. So now I'm going to take my clip removal tool, we're going to remove these four push clips, that'll give us access to move our wheel well out of the way.Now that we have those done, we'll move our wheel well out of the way to get access to our two Torx bolts behind here. So now that we got our push clips out, you're gonna just get in here, grab a hold of your wheel well. And down in here, there are little brackets that hold it in that kind of just go behind the fender. Don't be afraid to just give it a tug like that.And with your wheel turned in, this gives you access to get in here with a ratchet and a T20 Torx. That's where you're gonna be able to get to these two bolts back here, pull them out, and then our marker light will come out. So, now I'm gonna take my T20 Torx with my 1/4-inch drive ratchet inside here, there's one here, one down here. I'm gonna get back here with the ratchet.That's one. That's two. Now, the light will just come out. It's gonna be a little clip back here. I'm just gonna push down on a clip, remove the clip, and our light is out. We're ready to replace it with our LED. So, now we have our new LED light. It's pretty simple to install. We're gonna plug our connector back in for our light here, install it in here, put our two Torx screws back in, and then reinstall our inner wheel well.Now I'm gonna reinstall our electrical connection. Put our new LED light in. I'm gonna move our fender weld back out of the way again and hold it there. Take our Torx, get them started. It doesn't hurt to run them in on the new LED light before you install it, that way you have some threads because these are self-tappers.I take my 1/4-inch drive with my Torx. I'm gonna snug them both up. So now that both our Torx bits are in place and tight, you're gonna wanna reinstall your inner wheel well just like we did before. These two clips here, these little brackets that hold it in place, you're gonna have to push them in just like that. Gotta give them a shove. Put our push clips in and our one up top here.And now we have our inner wheel well in. We have our LED lighting. You're gonna wanna repeat the same procedure on the passenger's side. So, now that we got both our fronts in, now we're gonna start on our back. It's pretty much the same procedure that we did on the front. We're gonna remove our push clips right in here. Once we get them removed, we're gonna be able to take our wheel well out of the way and get behind to get our screws out.So now I'm gonna take my clip removal tool, get in here pop out our push clips that hold the inner wheel well on. And that's gonna give me access to the same deal as the front. You got little brackets here to hold it in. Now, these are a little bit tougher to get to, but we'll get in there with a 1/4-inch drive ratchet and remove our screws. So, we got our push clips out, we moved our inner wheel well. I pushed the inner wheel well back as far as I can get it because it is tight to get in here to get these two screws out.I found that the easiest way to get in here is going to be coming in from this side, your 1/4-inch drive with your T20. If you got big hands, you might wanna take your tire off and your wheel to get the wheel well out of the way, and then get up in there. I'm smaller, so I can get up in there. I'm gonna take my Torx, I already loosened them a little bit. That's one, and then there's another one up top here right around in this area right here. And like I said, they are a little tough to get to because they are jammed in there, but... Now I got that one pretty loose. Let me see if I can screw it up with my hand.Now I got our two Torx out. I'm gonna pull our marker light out, push down on our clip. Pop our clip off. Now we're gonna reinstall our new LED light. I'm just gonna push in the electrical connection. Put our marker light in place. We're gonna take our two Torx bits that we took out from the stock one. Reinstall them back in. It doesn't hurt to run them in a couple of times because they are self-tappers.Now that we have those in, I'm just gonna release the inner wheel well. I'm pushing it back there. And then we'll get it in place back where it was. Now we're going to install our push clips and hold our inner wheel well back in. Now you're gonna wanna repeat the same procedure on the passenger's side.That wraps up this review and install of our LED Side Marker Light Smoke. Thanks for watching. And for all things Charger, keep it right here at americanmuscle.com.
Subscribe to our YouTube Channel
Features, Description, Reviews, Q&A, Specs & Installation
CA Residents: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
(approx) 1 Hour
Simple installation for anyone.
What's in the Box
10 More Questions