Free Shipping On Orders Over $49. Details

Talk to a Mustang Expert
Every day 8:30AM EST - 11:00PM EST
Win Any Wheel & Tire Package! Enter Daily

JLT Performance Draw Through Air Box Intake (11-14 GT w/ Paxton or Vortech Supercharger)

AmericanMuscle no longer carries the JLT Performance Draw Through Air Box Intake (11-14 GT w/ Paxton or Vortech Supercharger). Please check out 2010-2014 Mustang Cold Air Intakes for an updated selection.
This item currently can not be added to your cart. Please try again later.

Features & Details

  • Improves Horsepower and Torque
  • Draw Through Design - (MAF Before Supercharger)
  • Seals to Hood and Uses Stock Fresh Air Inlet
  • 110mm MAF Housing Included
  • Designed for Paxton and Vortech Superchargers
  • Custom Tune Required for Operation
  • Fits 2011-2014 GT Mustangs
More Horsepower and Torque. Add even more power to your Vortech or Paxton supercharged Coyote Mustang by replacing the restrictive stock air box with a high flow replacement JLT Performance Air Box. The JLT Air Box will improve incoming air flow resulting in an additional 1.5 PSI of boost and horsepower gain at the rear wheels.

Money Saving Reusable Filter. This JLT cold air intake kit comes complete with a high flow reusable S&B brand air filter. So that means there is no need to go out and buy a new filter every few thousand miles. Now you can just clean the filter, re-oil it, save money, and go!

Draw Through Kit. The JLT Draw Through Air Box Kit includes a 110mm MAF housing, ABS Heat-shield with seal, 4.5” Flow tube, 4.5X9” S&B Powerstack reusable air filter, silicone reducer, all necessary clamps and a heat extractor hood insert for 2013-2014 models.

Application. This JLT Performance Air Box is designed for 2011-2014 GT Mustangs with an aftermarket Vortech or Paxton Supercharger installed. Requires re-tuning the vehicles computer for operation.

Fitment: 2011 2012 2013 2014 Details

CA Residents: Warning: California's Proposition 65

What's in the Box
  • (1) Intake Tube
  • (1) Air filter
  • (2) Silicone Couplers
  • (1) Heat Shield/Air Box
  • (1) 110mm MAF housing
  • (1) Heat extractor hood insert for 2013-2014 models
  • Clamps & all needed hardware
Installation Info
Tech Specs
Will it fit my Mustang?

You Might Also Like

Customer Photos

Questions & Answers (2)

2 Top Rated Questions

I was wondering which would make more power, the blow through or the draw through?

  • They both would provide similar power levels, however, a draw through system is typically easier to tune for than a blow through system.

Helpful (0)

Will this work with the stock inlet tube? I am wondering if this will work on the stock inlet tube and if you can tune for it. The reason I ask, is I know I will be running a vortech in the future, but currently would like to run a tune and intake till the car is paid off. Thanks for any info.

  • Not something that should be done. For best tune and performance you should have proper install.

Helpful (0)
Post Your Question

Customer Reviews (2) Write a Review

Overall Rating 5

out of 5 stars

Installation Time:Full Day

Installation Cost:$100-$250

  • Performance Gain 4.5 4.5
  • Fit 5 5

  • 5/5

    Installation Time: Shop Install

    Installation Cost: $100-$250

    January 24, 2014

    Draw Through Supercharger (11-14 GT)

    This product makes a considerable difference with overall performance! It's s must have with any Mustang!


    Year: 2011 Submodel: GT Londonderry N.H.

    Helpful (2)

  • 5/5

    Installation Time: Less than 1 Hour

    December 09, 2012

    Straight to the point.

    Install is straight to the point... takes about 5mins to throw on the intake pipe.


    Year: 2012 Submodel: GT Gulf Coast, Ms

    Helpful (2)

Related Mustang Categories