(approx) 20 Minutes
Simple installation for anyone.
$134.99 (kit)FREE Shipping
Saved - View your saved items
We're sorry. We couldn't save this product at this time.
What's going on, guys? Adam here with americanmuscle.com. We're taking a quick look at and installing the MMD Radiator Extension Covers fitting all '15 to '17 GT, EcoBoost, and V6 Mustangs. You should be taking a look at the extension covers if you're looking to cover up that side frame right behind your radiator shroud and behind your headlights to really blend in with the engine bay a little bit more. That is a pretty good weak spot that I think should've been covered up from the factory. This is a completely OEM-looking part that just blends in absolutely perfectly.It's gonna make the engine bay look a lot better on my buddy Will's 2016 GT with that Vortech supercharger. Coming in with some of that carbon fiber accents, this thing is gonna look so good with this installed. It covers up some of the hood latch wiring on the driver's side, no wiring whatsoever on the passenger's side, and it is an extremely simple install. As you can see from the back here, there's one strip of 3M automotive bonding tape. The other two are going to be simple push pin clips. One of those push pin clips already exists under the hood as one of the radiator shroud clips. We're just gonna pop that off, pop it right back in over top of our extension covers. There are two more push pin clip provided for you by MMD to make your life a little bit easier as well as some adhesion promoter and alcohol wipes to get the job done. Overall, you are looking at absolutely no longer than about5 minutes, maybe 10 at the absolute most, if you really wanna go to town and cleaning some of that frame but it's not necessary.I'm gonna show you guys how this gets done but I want to let you know, if you want to pick this set up, you can do so for just a little less than 140 bucks for your own S550. And in my opinion, like I said, look, this is something that should have come on the car from the factory so 140 bucks to really blend in some of that under hood dress up is going to go a long way especially for car show guys. Without further ado, guys, I want to show you how this gets installed, so let's go ahead and get our panel removal tool. All right guys, now before we can actually get this installed, I'm gonna set that aside for just one second. I'm gonna grab my panel removal tool and if you don't have one of these, a flathead screwdriver works just as well. We're gonna pop off this one clip here on our radiator shroud. Now, as you can see, when this does it in place, that's its positioning right there. So that clip here is gonna go. We're gonna pull that clip right out of this radiator shroud and pop it right back in over top of that hole.So let's set this aside and grab our tool here and we're gonna pop this off. Now again, a flathead screwdriver works just as well. This just makes life a little bit easier. We're going to set that aside for one second. Now, at this point, you have a couple of different options. You can set this right into place, put that push pin clip back over top, and use the one provided by MMD to pop it into place. Now that is option number one. Option number two is to take your alcohol wipes, clean off the area up here where the numbers are stamped into the metal, peel off the 3M tape on the back here, and really stick it into place. Now that's not an absolutely permanent installation, but that will make it a little bit more difficult if you wanna pop off your factory shroud to work on, say, your upper grille, your lower grille, maybe your front fascia is coming off. That way, you would have to heat gun that adhesion promoter off. Now, we are going to do that option to show you guys the full install here, so what we're gonna to do before we actually get this installed we're going to set that aside, grab our alcohol wipes.Now, as you can see, if you follow this frame a little bit farther back toward your strut tower, you'll see a bunch of numbers stamped right into your sidewall here. That's about the area that that 3M tape is gonna go, so grab that alcohol wipe there and just clean off the area, making sure that you're cleaning up all of the dust, whatever might be here from debris, clean off that area, so your 3M tape gets a really good bonding. All right, once you have that all cleaned up...All right, at this point, we're gonna take our adhesion promoter given to us in the kit here and just put a little bit of promoter right around that number. It'll give us a really, really good bond.Now that we have that in place, we can lay our extension cover down, line those up with our holes, and give that a firm push up by the 3M. From here, make our way back down to our factory radiator shroud. We're gonna use that push pin here that was given to us by MMD to snap it into place. Now we're gonna take our push pin click that we removed, pop it into our secondary one up here. All right. Now we can repeat this for the opposite side. Over here on the driver's side, the only difference in the install is going to be this cable here. We're gonna pop off these two clips holding it to the frame. Those come straight back.Now those are not going to be pushed into any new spot. We're gonna leave that loose. All right, with that cable loose, all we have to do is follow the exact same steps as we did on the other side. So I got my panel tool here, we're gonna pop off the clip on our factory shroud, use our alcohol wipes to clean our area, adhesion promoter, take off the red tape on the 3M, and stick it into place. Now, if you wanna pick up the MMD radiator extension covers for your own '15 to '17 GT, EcoBoost, or V6 Mustang, you can do so for about 140 bucks for the pair right here at americamuscle.com.
Subscribe to our YouTube Channel
Features, Description, Reviews, Q&A, Specs & Installation
Fitment: 2015 2016 2017 Details
CA Residents: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
(approx) 20 Minutes
Simple installation for anyone.
What's in the Box
10 More Questions