Customer Reviews (30) Write a Review

Overall Rating 4.2

out of 5 stars

Installation Time:Afternoon

• Fit 4.125 4.1
• Appearance 4.791667 4.8
• Bang For Your Buck 3.958333 4.0

• 5/5

  Installation Time: Afternoon

  October 08, 2018

  Nice Look

  Easy to install and gave my engine the face lift it needed.

  DaveS

  Year: 2010 Submodel: GT

  Helpful (2) Thanks for your input!

  • Fit 5

    5

  • Appearance 5

    5

  • Bang for your Buck 5

    5
• 3/5

  Installation Time: Afternoon

  August 02, 2018

  Tricky to fit, tolerances not held very well

  Tricky to fit, holes do not line up very well Can be hard to fit, really requires longer Studs manufactur should supply

  MCR

  Year: 2006 Submodel: GT

  Helpful (3) Thanks for your input!

  • Fit 1

    1

  • Appearance 4

    4

  • Bang for your Buck 3

    3
• 5/5

  Installation Time: Less than 1 Hour

  July 27, 2018

  Plenum and fuel rail covers

  Looks great after watching the installation video a few times the installation was very easy. Would be better if the studs and nuts were available in the kit as an option.

  BudC

  Year: 2007 Submodel: GT

  Helpful (3) Thanks for your input!

  • Fit 5

    5

  • Appearance 5

    5

  • Bang for your Buck 5

    5
• 4/5

  Installation Time: Less than 1 Hour

  July 20, 2018

  Easy install

  These are great! They look very clean and are quite easy to install. If you have a modified throttle body spacer or CAI you might have to make some adjustments like I had to. I had to remove my spacer on my 62mm throttle body to make room for the intake plenum but I think that the sacrifice is well work the look you receive.

  MatthewH

  Year: 2009 Submodel: GT

  Helpful (3) Thanks for your input!

  • Fit 3

    3

  • Appearance 5

    5

  • Bang for your Buck 4

    4
• 3/5

  Installation Time: Afternoon

  June 30, 2018

  Intake Plenum and Fuel cover on 07 GT/CS

  Although it is not made in other colors then Silver on Gray, I repainted mine to Blue on Black which looks better on my car. Given the steep price for this, it would be nice if other colors were an option. Also during installation one of the fuel rail mount Riv-nuts fell off the mount. I was able to replace it with one from the hardware store and my fathers hand held rivet driver. The mounting system needs to be engineered better to account for the engine wiring harness and fuel supply tubes on both sides of the engine. Overall I am happy with the appearance of the Speedform Intake Plenum and the Fuel Rail covers, after some modifications, I just wish the mounting system was better.

  MarkC

  Year: 2007 Submodel: GT

  Helpful (4) Thanks for your input!

  • Fit 3

    3

  • Appearance 5

    5

  • Bang for your Buck 3

    3
• 5/5

  Installation Time: Less than 1 Hour

  November 27, 2017

  My 06

  Really dresses up the top of motor and gives it a more powerful look

  BarryP

  Year: 2006 Submodel: GT

  Helpful (5) Thanks for your input!

  • Fit 5

    5

  • Appearance 5

    5

  • Bang for your Buck 4

    4
• 2/5

  November 16, 2017

  Plastic?

  In short, the entire set looks and feels like plastic. Not bad looking but it's not me. So I took the set around to various paint shops to pep the look up but as I showed them what I was trying to powder coat with paint, they were all amaze that the entire set was made out of plastic. I thought, they were correct and for the money I paid it didn't seem worth it. Thus, I sent the entire set back for refund. I paid almost $50.00 just to return the item at my expense.

  GermanO

  Year: 2006 Submodel: GT

  Helpful (6) Thanks for your input!

  • Fit 5

    5

  • Appearance 3

    3

  • Bang for your Buck 2

    2
• 5/5

  November 02, 2017

  intake plenum and fuel rail covers

  Was hesitant to pay this much for plastic covers but they are very thick and good quality. I painted these same color as car and they look fantastic. No regrets. they fit perfect and install only took about an hour.

  EricM

  Year: 2005 Submodel: GT

  Helpful (4) Thanks for your input!

  • Fit 5

    5

  • Appearance 5

    5

  • Bang for your Buck 4

    4
• 2/5

  October 17, 2017

  Incomplete

  The kit did not come with studs for the throttle body i had to special order them for my 2005 gt a big inconvenient

  RonaldA

  Year: 2005 Submodel: GT

  Helpful (4) Thanks for your input!

  • Fit 3

    3

  • Appearance 4

    4

  • Bang for your Buck 3

    3
• 4/5

  Installation Time: Afternoon

  August 18, 2017

  SpeedForm Intake Plenum and Fuel Rail Covers

  fits like a glove. cleans up the engine bay a lot. directions need to be a little more clear a step or 2 needs to be added to make it better. Must be very careful on the install not to mar , chip or scratch them that happens to easy with them parts. the Throttle body cover install need directions especially if your car does not come with one need a set of nuts added to the install kit.

  RickP

  Year: 2007 Submodel: GT

  Helpful (6) Thanks for your input!

  • Fit 5

    5

  • Appearance 5

    5

  • Bang for your Buck 5

    5
• 4/5

  Installation Time: Afternoon

  July 01, 2017

  wonderful

  It gives a very good view of my 2005 mustang engine . i like it .

  JackB

  Year: 2005 Submodel: GT

  Helpful (4) Thanks for your input!

  • Fit 3

    3

  • Appearance 5

    5

  • Bang for your Buck 4

    4
• 5/5

  Installation Time: Afternoon

  June 21, 2017

  Great Addition

  Finished off and made the finishing touch on my 2009 Bullitt engine.

  JoeS

  Year: 2009 Submodel: Bullitt

  Helpful (4) Thanks for your input!

  • Fit 4

    4

  • Appearance 5

    5

  • Bang for your Buck 3

    3
• 3/5

  Installation Time: Less than 1 Hour

  May 31, 2017

  They look great; Install, so-so

  These look great once they are installed in the engine compartment, but... Installation is a little tricky due to the fact that they are a generic fit for 05-10 GTs, which are not at all generic. The kit is also a bit pricey for molded plastic that scratches easily while installing it. Time for installation, once you have all the correct screws and a deep-well 5/32 socket, is less than an hour, not too bad, but for the price, all the screws should be with the kit ready to go so you don't have to go hunting for them (three stores, not everyone carries the recommended size or the replacement intake machine screws. The wiring bundles differ, the hose locations are slightly off, so you have to moderately modify them to accommodate these things to make them fit correctly. The stock bolts for the intake are just about 5/32 short, so you need longer bolts to install the intake and plenum covers properly. The side fuel rail covers have the mounting screws fairly far back, which is cumbersome to get to with the battery and master cylinder hampering the area. Also, the recommended screw length was a tad bit short to get a starting bite into the metal, two trips to the hardware store. Other than that, these are a great addition to your engine bay and will enhance the overall finished look that Ford should have done to begin with.

  JenniferY

  Year: 2005 Submodel: GT

  Helpful (6) Thanks for your input!

  • Fit 3

    3

  • Appearance 5

    5

  • Bang for your Buck 3

    3
• 5/5

  Installation Time: Afternoon

  April 07, 2017

  Fuel Rail Covers

  This is what my Mustang needed. A little dress up to the engine compartment. After reading the reviews I was ready for the driver side cover. The instructions pictures need to be a little bigger

  RidleyGT

  Year: 2010 Submodel: GT

  Helpful (5) Thanks for your input!

  • Fit 5

    5

  • Appearance 5

    5

  • Bang for your Buck 5

    5
• 5/5

  Installation Time: Less than 1 Hour

  March 31, 2017

  Good looking parts

  It looks great my 2006 Mustang . I will recommend it to anybody

  FrankN

  Year: 2006 Submodel: GT

  Helpful (4) Thanks for your input!

  • Fit 5

    5

  • Appearance 5

    5

  • Bang for your Buck 5

    5
• 3/5

  Installation Time: Less than 1 Hour

  March 13, 2017

  engine dress-up

  the two metal mounts for the fuel rail have the four nuts pressed on, no weld or anything else to hold them in place. two of the nuts fell off during install, everything has to be taken off to find the nuts and fix them properly, one side glue, other side pitched the nut and used a rivet cheap manufacturing for the money. once there are on they look great

  RussellB

  Year: 2006 Submodel: GT

  Helpful (5) Thanks for your input!

  • Fit 5

    5

  • Appearance 5

    5

  • Bang for your Buck 4

    4
• 5/5

  Installation Time: Afternoon

  December 20, 2016

  Intake Plenum and Fuel Rail Covers

  it was very easy to instal this product and it looks professional makes the engine compartment look very nice especially with the fuse box cover on it

  Horse

  Year: 2008 Submodel: GT

  Helpful (4) Thanks for your input!

  • Fit 5

    5

  • Appearance 5

    5

  • Bang for your Buck 5

    5
• 5/5

  Installation Time: Less than 1 Hour

  May 06, 2013

  Proud to pop the hood

  Very easy to install and looks great. Received several great comments at the last car show.

  07MrEd

  Year: 2007 Submodel: GT Portland, OR, USA

  Helpful (5) Thanks for your input!

  • Fit 5

    5

  • Appearance 5

    5

  • Bang for your Buck 5

    5
• 4/5

  Installation Time: Afternoon

  December 07, 2012

  Good Product very fragile finish

  This really dresses up the engine compartment. I looks great. However, the finish scratches off incredibly easily and I had issues with the mounting screws and alignment. The nuts that are pressed (?) on to the fuel rail cover mounting plates popped off leaving no place for a mounting location on the passenger side. After much agitation and some creative crazy gluing I got the mounting screw to start to thread. I have to change my plugs soon and am dreading removing this stuff, one because I don't want to scratch it and two I don't think I will ever get the passenger side re-threaded. Overall this kit dramatically changes the way your engine compartment looks for the better. I am happy now that everything is on and tightened up. I would just hate to ever have to remove it based on my experience.

  Storcho

  Year: 2005 Submodel: GT Sarnia, ON, Canada

  Helpful (7) Thanks for your input!

  • Fit 3

    3

  • Appearance 5

    5

  • Bang for your Buck 4

    4
• 5/5

  Installation Time: Afternoon

  October 06, 2012

  Exceptional look for engine!

  If you are looking to give your engine that finished look, the plenum covers will give you exactly that! I wish that I would have gotten this option with the vehicle. Fitment is good, however if you have a catch-can you may have to do some cutting and filing to work around.

  Quorra1

  Year: 2007 Submodel: GT WA

  Helpful (6) Thanks for your input!

  • Fit 4

    4

  • Appearance 5

    5

  • Bang for your Buck 5

    5