Free Shipping On Orders Over $49. Details

Talk to a Mustang Expert
Every day 8:30AM EST - 11:00PM EST
Win Any Wheel & Tire Package! Enter Daily

CDC Shaker System (2010 GT)

AmericanMuscle no longer carries the CDC Shaker System (2010 GT).
This item currently can not be added to your cart. Please try again later.

Features & Details

  • Muscular Styling
  • Functional for Better Airflow
  • NO Computer Re-Tune Required
  • Fits 2010 GT Mustangs
Muscular Styling. Classic Design Concept's Shaker System is now available for the new redesigned 2010 GT Mustangs. CDC's shaker system brings cool retro musclecar styling to the new redesigned S197.

Functional. This CDC Ram Air Cold Air Package includes all the duct work necessary to make it fully functional. The Shaker System includes an Engine dress up cover, Cast Aluminum Scoop and all the necessary hardware, instructions and templates. In addition CDC has engineered the Shaker with multiple water management systems to prevent water from entering the engine, making foul-weather driving concerns a thing of the past.

No Retune Required. The CDC Shaker System uses the stock air box so engine flashing is not necessary, leaving your emissions unchanged and warranty intact.

Fitment: 2010 Details

CA Residents: Warning: California's Proposition 65

What's in the Box
  • (1) Shaker scoop assembly
  • (1) Trim bezel
  • (1) Intake tube
  • (1) Coupler
  • (4) Hoses
  • (4) Zip ties
  • (4) Nuts
  • (4) Rivets
  • (1) Clip
  • (1) Bracket
  • Automotive bonding tape
Installation Info
Tech Specs
Will it fit my Mustang?

You Might Also Like

Customer Photos (11) Submit Your Photo

View All 11 Photos

Questions & Answers (11)

5 Top Rated Questions

V6? I noticed in the pictures this is on a V6.

  • This CDC Shaker system is meant for use only on the 2010 GT. This will not fit a V6.

Helpful (1)

Can this be added with a aftermarket air intake kit? Noticed the tube coming from the rear of the kit to the airbox.

  • This CDC Shaker System is designed for the stock air box, however, some enthusiasts have made this work with aftermarket intakes. We have not tested this shaker to work with aftermarket intakes and would not be able to confirm what would be required for the install.

Helpful (0)

Is there a measureable performance gain or gain in HP?

  • Classic Designs Concepts has not provided any dynamo-meter information regarding gains in horsepower or torque for their Shaker System.

Helpful (0)

Will this fit the s550

  • Unfortunately this CDC Shaker System is only intended for use on the 2010 Mustang GT. This will not work on a S550 Mustang.

Helpful (0)

will having a throttle body spacer installed and supercharger kit on it affect the install fit of this unit?

  • Hello! The CDC Shaker System is designed to work on a stock motor. It likely will not fit with a Super Charger or aftermarket throttle body.

Helpful (0)
Post Your Question
6 More Questions
Will this work if you have the Ford Racing Intake Manifold installed. I don't have it yet, I just want to know if it is possible to still be used if you have this. 1 answer
Hi. Can this system be painted? I guess if it can high temp plastic spray? Thanks! 1 answer
I am going to be 5.0 swapping my 2007 GT with the Aluminator Crate engine. What shaker system would provide the best fit? The 2010 model or the 2011-14 model? 1 answer
Will this fit over the top of the Roush M90 Supercharger, or is there going to be interference? 1 answer
The wife would like to add the shaker hood system to her 2010 GT Will this install with the Roush Cold air system presently on the car, or do I need to go back to the original air box? 1 answer
Does the Shaker System benifit or work in conjunction with CAI systems, or is there no point, since it is an intake system itself? 1 answer

Customer Reviews (8) Write a Review

Overall Rating 4.8

out of 5 stars

Installation Time:Full Day

  • Performance Gain 3.4 3.4
  • Fit 4.6 4.6

  • 5/5

    September 29, 2016

    Looks killer!

    The fit and finish is great and the install went well. I get compliments everywhere I go.


    Year: 2010 Submodel: GT

    Helpful (8)

  • 4/5

    Installation Time: Afternoon

    May 04, 2016

    Shake It!

    Great looking mod. The instructions are pretty good, but it would have been helpful to know that the template for the hole in the hood leaves about 1/4 to 3/8 inch of play for the trim ring. I spent about 30 minutes working to get the template 'dead nuts', only to find out that 'pretty close' would have been just fine. Also, if you use a jigsaw to make the cut, check the depth of cut...the underhood bracing from about the middle to the back side of the hood was about 1/8 too deep for my jigsaw to cut through, so I had to map out the cut on the underside and cut the bracing with a die grinder first...well, after the jigsaw blade jumped and made a few nice dents...thankfully they were on the cut/removed piece. A little over 4 hour install time. It's been installed for only a day, so I can't say I see a difference in performance, but so what if it doesn't? It looks awesome, and that's the point, right?


    Year: 2010 Submodel: GT

    Helpful (8)

  • 5/5

    Installation Time: Shop Install

    December 22, 2015

    Great Bolt-On

    It took me a few years to get around to adding this mod. But, in the end it was worth the wait. I had a collision shop install the entire thing (including the cut on the hood) and it costs $200. There was a noticeable increase in horsepower especially at the low end. The distinct looks helps stand out in a crowded field.


    Year: 2010 Submodel: GT San Antonio, TX

    Helpful (7)

  • 4/5

    Installation Time: Weekend

    December 04, 2015

    Shaker Hoop Scoop - DYI -

    Lets just start by stating " I am no Mechanic" but I felt very strongly that I could install this product by taking my time. The instructions state a 3 hour install, lets just say It took " A Lot " longer. To say I am pleased with the out come is a Huge Understatement, Turned out Fantastic. When I presented this project to my wife, she was not to happy with the idea of cutting a hole in the hood. I made sure she was not around when the cutting process "finally" happened, when I revealed the final Product, she was blown away, She Loved It.... (not more than me).......


    Year: 2010 Submodel: GT Saint Petersburg, FL

    Helpful (7)

  • 5/5

    Installation Time: Afternoon

    March 30, 2015

    Shaker Hood Install on a 2010 GT

    This was a pretty decent install, the instructions were pretty decent, except where you put the second set of nuts on the air inlet manifold. It tells you to put the second set on but that is before you put the shaker bracket on. I did have to make a modification to the front of the fixture so I could get the socket in under the fixture so I could tighten the nuts. Other than that it was a decent install and it looks awesome.


    Year: 2010 Submodel: GT Indiana

    Helpful (7)

  • 5/5

    Installation Time: Full Day

    October 18, 2012

    Constant Compliments!

    Easily the most stressful addition that has been added to my mustang. Cutting into the hood was the point of no return, but afterwards, it was easy place and tighten. I have had numerous compliments and never have had an issue. I also have purchased the Ford Racing Hot Rod Cams from American Muscle and it makes that scoop really shake. I made a quick video at ....the audio does not give the deep rumble that the car actually has. Hope this helps.


    Year: 2010 Submodel: GT Massachusetts, USA

    Helpful (9)

  • 5/5

    February 26, 2010

    Awesome Kit!

    Installed it over the weekend and man it looks fantastic! Car seems to have a little more power in the low end. A must for that retro look we all love!


    Helpful (20)

  • 5/5

    February 03, 2010




    Helpful (8)