Customer Reviews (21) Write a Review

Overall Rating 3.1

out of 5 stars

Installation Time:Afternoon

• Performance Gain 1.545455 1.5
• Fit 2.090909 2.1

• 5/5

  Installation Time: Less than 1 Hour

  March 27, 2018

  Gasket

  Fits good and doesn’t leak, might as well buy a good brand gasket if you are doing this job.

  DevonT

  Year: 2004 Submodel: GT

  Helpful (2) Thanks for your input!

  • Performance Gain 1

    1

  • Fit 5

    5
• 1/5

  Installation Time: Afternoon

  July 10, 2017

  Do not buy!

  Used gaskets for startup on new build leaked coolant from rear and front of intake. Followed proper torque specs ect. Went to remove intake and gasket is glued to heads and intake so now in have to scrape the residual stuck gasket pieces without damaging or affecting the aluminium on my heads and intake definitely not worth the headache go with OEM gaskets.

  JoseC

  Year: 2003 Submodel: GT

  Helpful (1) Thanks for your input!

  • Performance Gain 1

    1

  • Fit 1

    1
• 1/5

  Installation Time: Afternoon

  December 10, 2016

  DO NOT BUY

  Horrible gaskets failed as soon as I started my car after the instal. Waste of time and money and I now have coolant in my oil and valves. AM shouldn't even be selling this product it's terrible.

  Joedog

  Year: 2000 Submodel: GT

  Helpful (3) Thanks for your input!

  • Performance Gain 1

    1

  • Fit 1

    1
• 4/5

  August 29, 2016

  not perfect

  These gaskets are not perfect but do the job. I was hoping for the plastic O-Ring gasket that comes from the factor on my motor however these are paper gaskets. they are a little bigger than they need to be and stick out underneath the manifold. Seems like all ports line up though

  Reno

  Year: 2002 Submodel: GT

  Helpful (2) Thanks for your input!
• 1/5

  June 09, 2013

  professional gaskets

  Do not buy these because could not get a good seal. Had to go to a ford dealer and buy ford gaskets to get a good seal. I wasted a lot of time and the price of the professional gaskets. I do like the intake manifold. $30.00 bucks down the drain.

  MotorCityHoonigan

  Year: 2001 Submodel: GT

  Helpful (4) Thanks for your input!

  • Performance Gain 1

    1

  • Fit 1

    1

  • Bang for your Buck 1

    1
• 1/5

  Installation Time: Afternoon

  May 18, 2013

  thin Intake manifold gasket that only had sealant on one side

  this gasket leaked before i even started the engine. The gasket was too thin or the intake manifold that i purchased from Amerian Muscle was warped and uneven so I had to reinstall with a thicker gasket that i had with a better o-ring type sealing surface. I would like a refund for money spent on the gasket that failed for whatever reason and if the manifold developes a leak again after installing it with a thicker gasket i will be asking a refund on the intake manifold also. Hope we can get past this as i have always had good luck with you guys in the past.

  Woodson

  Year: 2001 Submodel: GT Vancouver, WA, USA

  Helpful (2) Thanks for your input!

  • Response from AmericanMuscle

    These Typhoon Gaskets are intended to be used with Typhoon Intakes Manifolds only, which is why it didn't mate properly with your PI Intake Manifold. With the correct gasket, you won't have any leaking problems with your new PI intake manifold. Give our customer service a call so that we can get you a refund on these gaskets.

    Lisa, Customer Care
    

  • Performance Gain 1

    1

  • Fit 1

    1

  • Bang for your Buck 1

    1
• 4/5

  Installation Time: Afternoon

  May 14, 2013

  good fit

  Nothing really special about these gaskets, too early to say really how good they are.

  Vader99

  Year: 1999 Submodel: GT Grand Prairie, TX, USA

  Helpful (1) Thanks for your input!

  • Performance Gain 3

    3

  • Fit 3

    3

  • Bang for your Buck 3

    3
• 2/5

  Installation Time: Less than 1 Hour

  December 15, 2012

  Faulty product

  I purchased this product to go with the Typhoon intake manifold I purchased. When I opened the package I realized that the "Silicone Bead" was missing from one of the gaskets. This alone was a major bummer as it caused me to delay the installation for another week. I contacted Precision-Products and they shipped me out a new set of gaskets immediately. Other than that minor issue the product and service are great

  ricktaylor

  Year: 2000 Submodel: GT California

  Helpful (3) Thanks for your input!

  • Performance Gain 2

    2

  • Fit 1

    1

  • Bang for your Buck 2

    2
• 5/5

  Installation Time: Afternoon

  September 06, 2012

  great choice

  The intake gaskets were a good choice for me though intake gaskets are not a big performance enhancer the intake spacers I have to go with the gaskets is a big gain.

  Racing52

  Year: 1998 Submodel: GT Houston TX

  Helpful (2) Thanks for your input!

  • Performance Gain 2

    2

  • Fit 5

    5

  • Bang for your Buck 3

    3
• 1/5

  Installation Time: Afternoon

  February 20, 2012

  Bad Gasket

  Installed the intake gasket correct. When i went to start the car i had antifreeze pouring out the motor and also blowing out the exhaust. Pulled it all back apart and everthing was precisely where it needed to be. The gasket definitely wasn't one of my best perchases

  Mick1

  Year: 2003 Submodel: GT

  Helpful (3) Thanks for your input!

  • Performance Gain 1

    1

  • Fit 1

    1

  • Bang for your Buck 1

    1
• 3/5

  Installation Time: Afternoon

  January 27, 2012

  They're Alright

  I ordered a set of these when I replaced my intake with a Professional Products Typhoon Intake Manifold. The stock gaskets looked like they might seal better, but these seem to be performing pretty well with no problems, so I can't complain.

  ModularCal

  Year: 2002 Submodel: GT Virginia Beach, VA

  Helpful (2) Thanks for your input!

  • Performance Gain 3

    3

  • Fit 3

    3

  • Bang for your Buck 3

    3
• 1/5

  Installation Time: Afternoon

  November 02, 2011

  Garbage Gaskets

  These gaskets are garbage, hands down. Ordered a set along with an aluminum intake manifold. First off, these gaskets are roughly half the thickness of the stock gaskets. This wouldn't be important except for the fact that clearance of the typhoon manifold and the coolant pipe underneath are a big issue. Every 8th of an inch is important. Asides from this, these gaskets are very cheaply made! They don't any metal where the bolts go through, while the ones sold at auto stores do. Also there were only rubber seals on one side, while once again the auto stores sell ones with seals on both sides. If you have 30 bucks to waste then buy them! Otherwise go to your local auto parts store, spend the same 30 bucks and get a much higher quality product.

  GTforever

  Year: 2001 Submodel: GT OKC

  Helpful (5) Thanks for your input!

  • Performance Gain 1

    1

  • Fit 1

    1

  • Bang for your Buck 1

    1
• 1/5

  June 28, 2011

  Do not recommend

  Would not recommend gasket failed on startup going with fel-pro

  Sean

  Year: 2001 Submodel: GT

  Helpful (6) Thanks for your input!
• 1/5

  May 20, 2011

  I would not recommed them

  Really fast shipping, But ive went through 2 sets of these gaskets and they still keep failing, just gunna go with some fel pro's.

  Mike

  Year: 1999 Submodel: GT

  Helpful (3) Thanks for your input!
• 5/5

  May 16, 2011

  Typhoon Intake manifold gaskets

  Would not recommend gasket failed on startup worked on engines 20 plus years had to disassemble and replace used felpro and worked fine with no leaks

  John Wesnesky

  Year: 1999 Submodel: GT

  Helpful (4) Thanks for your input!
• 5/5

  April 01, 2011

  Professional Products Typhoon Intake Manifold Gasket (96-04 4.6L 2V)

  After my recalled factory intake manifold blew, I went ahead and started browsing for full aluminum manifolds. I liked it because it provides great flow, and can handle Nitrous without blowing. It was easy as replacing the stock manifold, just a little heavier, might need another set of hands. If your looking to do NO2 then go ahead and purchase this, plus you can always have the runners ported even more.

  Cody

  Year: 2000 Submodel: GT

  Helpful (3) Thanks for your input!
• 5/5

  March 31, 2011

  PI-Intake

  Love my new intake manifold great performance and easy to put on. Feel the difference on the GT.. I would recommend this for you Mustang

  George Gutierrez

  Year: 2000 Submodel: GT

  Helpful (3) Thanks for your input!
• 5/5

  February 27, 2011

  Gaskets

  The gasket was simple and easy to use. i would recomend this product any day.

  Miguel Arango

  Year: 2002 Submodel: GT

  Helpful (2) Thanks for your input!
• 5/5

  September 29, 2010

  2nd set

  I had bought a set of these when i ordered my PP intake plenum, and worked fine, but it failed on cylinder 8 so i had to go ahead and order another set. I belive it wasnt sitting right, so hopefully the new set doesnt fail on me. Gasket is a much better quality than factory A suggestion for anyone having trouble lining them up right, find at least two bolts the similar size as the plenum bolts, longer if possible, cut the head off, and with a grinder, make a notch so that a flat head can fit. place bolt into the holes, just enough so they hold in place, and you can place both the gaskets, and plenum in, just lining up the holes with the bolts in place. with the plenum in place, go ahead and put at least two bolts in(with heads) and remove the other two that were used as a guide. Same concept used when replacing heads on a block. Hopes this helps

  Cj Cruz

  Helpful (10) Thanks for your input!
• 4/5

  January 20, 2010

  gasket

  Worked fine just wish it had the tabs on it like the stock gasket to hold it in place while your trying to put the intake manifold in.

  Irish

  Helpful (2) Thanks for your input!