BBK Caster Camber Plates (94-04 All)

Customer Reviews (33) Write a Review

Overall Rating 4.8

out of 5 stars

Installation Time:Afternoon

Installation Cost:$100-$250

• Handling Improvement 4.84375 4.8
• Fit 4.90625 4.9
• Bang For Your Buck 4.53125 4.5

• 5/5

  Installation Time: Afternoon

  July 24, 2012

  Must have for lowered Mustangs

  I have a 99 GT that needed caster/camber plates to get it properly aligned. I first went cheap & bought the J & M plates; BIG mistake. The J & M plates are very loud and not well built. It sounded like my front end was going to fall out every time I hit a bump! I purchased the BBK Plates and now I have quiet in the car, improved handling and a very solid feel to it. The handling is great and the look that they add is fantastic! The BBK plates have bushings on the top & bottom of the top strut mount which helps to contain the noise & provides a "solid" feel; J & M does not. Installation was easy and complete within 2 hours. It helps if you have a bench grinder to modify the top rubber piece of the existing strut cover. Upon completion! I took it it in for a front end alignment which was done in no time due to how easy it is to make adjustments on them. These are a must have for you lowered Mustang!

  GlimmerTwin34

  Year: 1999 Submodel: GT Paso Robles, CA 93446, USA

  Helpful (4) Thanks for your input!

  • Handling Improvement 5

    5

  • Fit 5

    5

  • Bang for your Buck 5

    5
• 5/5

  September 04, 2016

  Great Camber Plates

  Used to have a nasty clunk noise that could not figure it out where was coming from till a mechanic pointed out the old SR CC Plates that were broken in both sides. Decided to go for the BBK CC Plates and what a relief, no more clunk and able to get the alignment back to factory specs. This plates are really good is a little expensive but are worth it. The car runs really great w/o that nasty and embarrassing clunk sound. I really recommend this product.

  Xavier15

  Year: 2004 Submodel: GT

  Helpful (1) Thanks for your input!
• 5/5

  Installation Time: Afternoon

  June 09, 2015

  BBK casters rock, full adjustment and no clunks

  First class camber plates that work as good as they look. Installation was a brease with no new holes to drill. I was very pleased that the clunking from a competitor design was now gone. It is a pleasure to drive my Mustang again.

  PapaJeff

  Year: 2004 Submodel: Mach 1 Plover Wi

  Helpful (1) Thanks for your input!

  • Handling Improvement 5

    5

  • Fit 5

    5

  • Bang for your Buck 5

    5
• 5/5

  Installation Time: Less than 1 Hour

  June 09, 2015

  BBK camber/caster

  Great fit, looks really clean, the way they adjust feels smooth and solid.

  Paul

  Year: 2003 Submodel: Cobra Texas

  Helpful (1) Thanks for your input!

  • Handling Improvement 5

    5

  • Fit 5

    5

  • Bang for your Buck 5

    5
• 5/5

  Installation Time: Less than 1 Hour

  May 20, 2015

  Beautiful.

  Great product. Needed an aftermarket set of Caster/Camber plates to fine tune my alignment. Did some research and these BBK plates had great ratings.. And for good reason. High quality product, looks amazing under the hood. Install was very easy and straight forward. Took it to the shop i work at and got it on the rack. Install took about 20 minutes. Thanks AM for another A product.

  Layla99cobra

  Year: 1999 Submodel: Cobra Sacramento, CA

  Helpful (1) Thanks for your input!

  • Handling Improvement 5

    5

  • Fit 5

    5

  • Bang for your Buck 5

    5
• 5/5

  Installation Time: Less than 1 Hour

  May 17, 2015

  01 mustang

  the product was great fit perfect in my 01 mustang the only complaint i have at all was the packaging i was missing 2 out of 6 bolts so i had to put two old ones back on really no big deal but they still fit perfect

  mickey

  Year: 2001 Submodel: Other philly,pa

  Helpful (1) Thanks for your input!

  • Handling Improvement 5

    5

  • Fit 5

    5

  • Bang for your Buck 3

    3
• 5/5

  Installation Time: Shop Install

  Installation Cost: 0-$100

  May 14, 2015

  Great buy, great results.

  I bought these caster camber plates to enhance my handling at the autocross events I run monthly. I had the shop put 2 degrees of negative camber in the front end. It enhanced my cornering greatly without increasing my tire wear. I'm very pleased with the results and they are worth every penny. Thank you American Muscle for helping me out yet again!

  Dave94

  Year: 1994 Submodel: GT St. Pete, FL

  Helpful (1) Thanks for your input!

  • Handling Improvement 5

    5

  • Fit 5

    5

  • Bang for your Buck 5

    5
• 5/5

  Installation Time: Less than 1 Hour

  December 21, 2014

  BBK Caster Camber Plates

  These things look great under my hood. They took no time to put on. They are quiet and make no noise at all. Plus AM super fast shipping makes it even better.

  1996SVTCOBRA

  Year: 1996 Submodel: Cobra Dallas, GA, USA

  Helpful (1) Thanks for your input!

  • Handling Improvement 5

    5

  • Fit 5

    5

  • Bang for your Buck 5

    5
• 5/5

  Installation Time: Afternoon

  April 15, 2014

  Better then bearing style

  Want to start by saying I had bearing style cc plates on my Cobra....those were so noisy, it sounded like someone hitting metal with a hammer. My wife said " the wheels sound like they will fly off!" My car felt unsafe to me...until i saw these here on AM. i called to get some info on them as i wanted to know more about the poly strut bushing. Long story short, these are QUIET!! Sounds like....NOTHING at all! I LOVE these plates. AM even let me return the "other" type ones back to them for a full refund, after they were on my car for a while. If you know your way around a car, these will be a cinch to install. Took me about an hour per side from wheel off to back on

  AOL3StevieMeth

  Year: 1998 Submodel: Cobra south Jersey

  Helpful (1) Thanks for your input!

  • Handling Improvement 5

    5

  • Fit 5

    5

  • Bang for your Buck 5

    5
• 5/5

  Installation Time: Less than 1 Hour

  April 04, 2014

  No more buying front tires every 6 months!

  This was a great buy... My wheels no longer go bald on the inside and the car handles better in turns. If you know what you're doing the install for both sides should take 45mins to 1 hour.

  Dazedglobe

  Year: 2004 Submodel: GT

  Helpful (1) Thanks for your input!

  • Handling Improvement 4

    4

  • Fit 5

    5

  • Bang for your Buck 5

    5
• 5/5

  Installation Time: Less than 1 Hour

  April 02, 2014

  Great product

  Needed for any mustang getting lowered! Good quality product too. Had a problem with a missing washer but went to a local hardware store and found one similar enough to wirk

  Doku

  Year: 1997 Submodel: Cobra Lafayette, IN, USA

  Helpful (1) Thanks for your input!

  • Handling Improvement 5

    5

  • Fit 5

    5

  • Bang for your Buck 4

    4
• 5/5

  Installation Time: Afternoon

  January 12, 2013

  Caster Camber plate installation

  This product is not so much a handling improvement but it greatly increases the life of your tires if the car has been lowered. Just be sure to have the car aligned once you have installed the plates. The installation took me about an hour per side and was fairly easy provided you have the proper tools.

  ricktaylor

  Year: 2000 Submodel: GT California

  Helpful (1) Thanks for your input!

  • Handling Improvement 4

    4

  • Fit 5

    5

  • Bang for your Buck 3

    3
• 5/5

  Installation Time: Afternoon

  June 20, 2012

  BBK caster camber plates

  They look great and are very easy to install. One of the only ones I've seen that let you get better handling while still keeping a decent ride quilty by keeping a bushing. Great part.

  David0715

  Year: 2000 Submodel: GT Leonardtown, MD

  Helpful (1) Thanks for your input!

  • Handling Improvement 5

    5

  • Fit 5

    5

  • Bang for your Buck 5

    5
• 5/5

  Installation Time: Shop Install

  March 23, 2012

  camber plates

  The plates look too sick. They give the under side a pop once you open the hood. The handling improved by getting tighter and feeling more beefy when you turn. Heck of a product from looks to performance. A must have for any lowered stangs. Recommend? Definitely.

  ButchN8Ball

  Year: 1999 Submodel: Cobra Las Cruces, NM

  Helpful (1) Thanks for your input!

  • Handling Improvement 5

    5

  • Fit 5

    5

  • Bang for your Buck 5

    5
• 5/5

  Installation Time: Less than 1 Hour

  March 18, 2012

  bbk's cc plates

  bought these second hand, didnt have instructions or anything like that just read the ones off MM. took me about 30mins tops very easy

  03gtt

  Year: 2003 Submodel: GT my casa

  Helpful (1) Thanks for your input!

  • Handling Improvement 5

    5

  • Fit 5

    5

  • Bang for your Buck 4

    4
• 5/5

  Installation Time: Afternoon

  January 27, 2012

  Better then my upr

  They installed just fine look and work great! I'm happy with how she rides now, she feels tighter and looks great under the hood this is a great product and would recommend it to any one

  Itmoves

  Year: 2004 Submodel: Mach 1 New Jersey, NJ

  Helpful (1) Thanks for your input!

  • Handling Improvement 4

    4

  • Fit 5

    5

  • Bang for your Buck 5

    5
• 5/5

  Installation Time: Afternoon

  July 10, 2017

  Alignment made easy!

  Get yourself a set of these if you're thinking about lowering your mustang. I dropped mine about 2" and these plates made the adjustment of the alignment a lot easier. Good product, highly recommended.

  JuanO

  Year: 2002 Submodel: GT

  Helpful (0) Thanks for your input!

  • Handling Improvement 5

    5

  • Fit 5

    5

  • Bang for your Buck 5

    5
• 2/5

  Installation Time: Afternoon

  April 27, 2017

  Pics very deceiving!

  I went with the BBK Casters for the polished look, returned the first set looked very dull, thought maybe they were bad, well 2nd pair looked the same, returned thought third time was the charm, but no, all 3 of them do not match the polish of the pictures that they show, they work great, but again bought for the look too.

  TheHag82

  Year: 2002 Submodel: GT

  Helpful (0) Thanks for your input!

  • Handling Improvement 5

    5

  • Fit 5

    5

  • Bang for your Buck 2

    2
• 4/5

  Installation Time: Shop Install

  Installation Cost: $100-$250

  April 19, 2017

  98 Experience

  I needed an experienced mechanic to install the plates as it was difficult. The plates allowed more alignment but, no quite enough. The mechanic who installed the plates must grind off about 1/4" of the Mustang top frame so the strut may be moved a little more to get Camber alignment in the green. However, I can feel the difference in the front end when driving that I haven't experienced in many years. It rides smoother.

  RobertA

  Year: 1998 Submodel: GT

  Helpful (0) Thanks for your input!

  • Handling Improvement 5

    5

  • Fit 3

    3

  • Bang for your Buck 3

    3
• 5/5

  Installation Time: Weekend

  April 11, 2017

  Mach1

  The look great and the are easy to install i recomend this parts

  JoseM

  Year: 2004 Submodel: Mach 1

  Helpful (0) Thanks for your input!

  • Handling Improvement 5

    5

  • Fit 5

    5

  • Bang for your Buck 5

    5